Wireless Communications in Smart Rail Transportation Systems

As transportation systems become more automated, vehicles have an increasing demand on communications and are being equipped with more wireless communications services and sensors.

0
250
Advertisement

Abstract

Railway, subway, airplane, and other transportation systems have drawn an increasing interest on the use of wireless communications for critical and noncritical services to improve performance, reliability, and passengers experience. Smart transportation systems require the use of critical communications for operation and control, and wideband services can be provided using noncritical communications. High speed train (HST) is one of the best test cases for the analysis of communication links and specification of the general requirements for train control and supervision, passenger communications, and onboard and infrastructure wireless sensors. 

The article analyses in detail the critical and noncritical networks mainly using the HST as a test case. First, the different types of links for smart rail transportation are described, specifying the main requirements of the transportation systems, communications, and their applications for different services. Then, based on findings a network architecture and requirements of the communication technologies for critical and noncritical data has been proposed. Finally, an analysis is made for the future technologies, including the fifth-generation (5G) communications, millimeter wave (mmWave), terahertz (THz), and satellites for critical and high-capacity communications in transportation.

Introduction

Wireless technologies have been widely developed in the last years and now are ready to meet the increasing demands of communication services for control, operation, and maintenance of smart transportation systems. Existing radio technologies include Wi-Fi, WiMAX, Long Term Evolution (LTE), wireless sensor networks, wireless ad hoc networks, and particularly future fifth-generation (5G) technologies that will highly focus on the development of intelligent transportation systems of terrestrial and aerial vehicles. These emerging technologies can significantly improve the operation, efficiency, reliability, and passengers’ experiences, but each communication network must be designed and configured to meet the special requirements of each transportation system.

Nowadays, transportation systems have an important demand of communications with very strict requirements of quality, capacity, and reliability. One of the best ‘test cases’ for the analysis of communications in transportation systems is high speed train (HST). In a HST communication network, two types of communications: critical and noncritical communications can be propounded.

Critical communications between HST and infrastructure are used for the control signalling to increase speed, efficiency, safety, and reliability. These communications are critical because they are necessary for the high-performance operation of the transportation system so that it must have a very high reliability and availability (>99%). Nevertheless, it is important to remark that communications are not responsible for the security. Security depends on other systems installed onboard or in the infrastructure. For example, if a HST is considered, Global System for Mobile Railway (GSM-R) communications are used now to transmit telemetry (position) of the train and to send movement authorizations to it. This information is necessary to increase the speed of the train higher than 300 km/h and must be updated every 100 ms. If it is not updated during 1 second, there will be an emergency process reducing the speed of the train to a safe value. To guarantee this performance it is necessary to achieve very high quality communications systems with redundancy and improved reliability. GSM-R is widely used in HST, but, currently, railway operators want to improve the performance of the trains and move to automatic driving so that they need a new high-capacity wireless communication system able to include high quality video transmissions from train to control center.

Another example could be the use of Unmanned Aerial Vehicles (UAVs) to improve security and reliability of smart rail transportation. As proposed in, these platforms can be used to enable and improve the communications and operation of next generation of smart transportation systems. For these applications, UAVs need also a critical communication link and a payload link. Critical communication link is used to send position of the UAV from air to ground, and to send control commands or waypoints to the UAV. There will be also a noncritical communication link that can be used for several purposes like video transmission for railway incident or infrastructure monitoring, or as a moving relay for emergency communication.

Thus, in both cases, the use of critical communications is mandatory, and these communications must have high quality of service because although security does not depend on them, frequent fails on communications can reduce reliability. For these reasons, a critical communication system has very special requirements and must rely on a very well proved technology specially customized for the smart transportation system. For example, HSTs are still using GSM-R standard, and commercial UAV radios use mainly early frequency hopping technology.

Noncritical communications are used for payload, supplementary services, and passenger services. In this case, broadband communications for supplementary services like high-definition video and data services of the passengers is required. Some examples could be a video link transmitted by a UAV or a wideband Internet for the passengers of a high speed train. In both cases the principal requirement is capacity, so the design of these communications is completely different. Currently, these communications are on continuous development and are one of the principal challenges for the next years and for 5G technologies.

Finally, wireless sensors and ad hoc networks used for security and monitoring are now being used to provide supplementary services to vehicles, and the use of millimeter wave (mmWave), terahertz (THz), and satellites will be relevant in the future to provide vehicle-to-vehicle communications, radar sensors, and onboard communications for different vehicle applications.

Communications for Smart Rail Transportation

As transportation systems become more automated, vehicles have an increasing demand on communications and are being equipped with more wireless communications services and sensors. However, the maximum data rate of commercial communication systems (e.g., 4G) is still limited to 100 Mb/s for high mobility, and, therefore, current technologies are not sufficient to handle the terabyte-per-hour data rates that can be generated in next generation vehicles. Likewise, railway communications are required to provide various high data rate applications for passengers and train service. These applications need to be implemented in five rail scenarios:

  1. Train-to-infrastructure (T2I) (HD video and other information in real time transmitting among various infrastructures)
  2. Interwagon (wireless network between wagons)
  3. Intrawagon (links between user equipment and access points of a wagon)
  4. Inside station (links between access points (APs) and user equipment (UEs) in train/metro stations)
  5. Infrastructure-to-infrastructure (I2I) (HD video and other information in real time transmitting among various infrastructures) (note that whether this I2I scenario belongs to railway communication depends on whether this link is managed by railway industry; in most countries, the I2I link is provided by communication network operator, but in some countries, like China, such link is owned and managed by railway corporations.)

For the scenarios ‘inside station’ and ‘infrastructure-to-infrastructure,’ the bandwidth requirements are from several hundred MHz to several GHz, depending on concrete conditions. For the scenarios ‘intrawagon’ and ‘interwagon,’ 1–10 GHz bandwidths will be required, respectively. As the main interface between the network on train and the fixed network, the scenario ‘train-to-infrastructure’ transmits an aggregated stream of the inter/intrawagon scenarios. Therefore, it requires the bandwidth of several GHz to accommodate over 100 Gbps data rates. Such high data rate and huge bandwidth requirements form a strong motivation of exploring the underutilized mmWave and even THz bands. From the wireless channels viewpoint, there are numerous open challenges and chances on researching and developing mmWave and THz terrestrial and satellite communications enabling smart rail transportation [9]. Among all the above five scenarios, the most challenging one is the T2I scenario. As the main interface between the network on train and the fixed network, the T2I channel suffers strong dynamics, Doppler spread, and shadowing. Thus, it has drawn great attention, and, therefore, we mainly discuss it in the rest of the paper, rather than briefly talking about all of the five scenarios with equal weight.

Critical Communications

In contrast to the rapid and innovative changes in commercial mobile communications, the development of critical communications in public transportation has been rather more measured, mainly because of the mission-critical requirements. Among all the critical communications in railway, the GSM-R is the most widely used standard, and its stability has been verified for more than 10 years. However, due to limited transmission capacity, GSM-R has been applied mainly to data communications for train control.

In order to provide new railway services such as video supervision and real-time monitoring, research efforts are now oriented towards LTE as the next generation technology. In particular, the capabilities of LTE in terms of future railway operational needs are currently being reviewed under the Future Railways Mobile Communications System (FRMCS) project, which was initiated in 2013. Recently, the authors in have proposed LTE Railway (LTE-R) as an integrated wireless railway communications system by validating a deployed testbed of LTE-R. Moreover, ‘signal quality on the top of and inside train,’ ‘chain type network deployment,’ and ‘guaranteeing quality of services (QoS) for safety services’ are the main critical issues that need further and deeper technical consideration:

  1. Signal quality on the top of and inside train: when using the direct access mode for both the onboard terminals (usually on the top of the train or car) and mobile terminals inside the train or car, the most critical issue during cell optimization is the achievement of a target level of received signal strength for both onboard and mobile terminals. This is mainly because the signal from the base station that penetrates directly into the car suffers the penetration loss up to 24 dB. Such difference of the two channels, on the one hand, poses much higher requirements for the transmission power of the base station and, on the other hand, requires careful design of the antenna parameters of the two types of receivers in order to ensure a certain level of signal quality simultaneously for both onboard and mobile terminals. When using the two-hop access mode—one T2I hop and one intrawagon hop—such challenge coming from the huge penetration loss of the train body can be avoided.
  2. Chain type network deployment: rather than the hexagonal type cell structure in commercial networks, railway (or vehicular) dedicated communication networks use a cell structure of a sequential chain type. Because of this uniqueness of a dedicated network, the communication scheme has the chance to be optimized further with low complexity and without loss of optimality.
  3. Guaranteeing QoS for ultrareliable low latency applications: safety-critical vehicular applications can be broadly classified as vehicle detection, road detection, lane detection, pedestrian detection, drowsiness detection, collision avoidance, and so forth. All these applications assist drivers and reduce potential accident risks and therefore require ultrareliability and low latency (e.g., the allowable latency for Traffic Signal Violation Warning (V2I) is 100 ms, while the allowable latency for vehicle collision warning (V2V) is 20 ms). For railway, typically all safety-based services need the highest safety level (SIL4), low bandwidth (less than 1 kb/s per train), significant delay constraints (less than 500–800 ms in the worst case, usually even less), and the traffic pattern is usually real-time variable bit rate (RT-VBR). Voice calls need higher data rates (i.e., 64 kb/s depending on the codec). A good reference for maximum jitter could be 30 ms. Therefore, in order to support these services, it is important to keep data connectivity at the highest priority level. To do so, the network design for critical communications in public transportation must make use of sophisticated network management schemes for handling exceptional situations such as traffic congestion.

Noncritical, Broadband Communications

High-capacity communications networks for payload services and passengers on transportation are beginning to develop nowadays. Passengers on HSTs, metros, airplanes, and boats demand the use of communications like the ones they have in their private vehicles or at their homes. Also, transportation system operators demand supplementary services like the following:

  1. Onboard and wayside high-definition (HD) video surveillance that is critical for safety and security concerns (e.g., cars stuck on railway crossings, terrorist attacks).
  2. Onboard real-time high data rate connectivity for web browsing, video conferencing, video broadcast, and so forth.
  3. Real-time train dispatching HD video between train and train control centers (TCCs) required for train dispatching and future driverless systems as well as journey information that are dynamically updated for all passengers.

However, the implementation of these communications in smart transportation systems has an important complexity because each transportation system has its own special characteristics: number of users, maximum speed, vehicle construction, vehicle infrastructure, and others. For these reasons, it is necessary to design and adapt the communication network for each specific transport system, and, therefore, public networks for critical communications can be used. 

According to the specifications of the transportation system, it is necessary to efficiently use the public terrestrial infrastructure combined with other technologies to increase capacity and performance. Therefore, the use of 4G LTE networks must be combined with moving relay solutions onboard trains and then combined with satellite networks and other 5G terrestrial networks to improve capacity and to reduce cost. It is, therefore, necessary to provide broadband services to users considering the characteristics of this means of transport and its peculiarities, which for HST are summarized in a data capacity close to 1–10 Gbps to provide broadband services up to 1500 users, who are going to maintain an intense connectivity. To this end, there is the problem of HST which makes it difficult to use terrestrial networks on desserts or inhabited areas that are frequently crossed by new HST. On the other hand, the frequent tunnels make it difficult to use the satellite, so a mixed solution must be used.

This network must be capable of providing broadband communications to train passengers; for this purpose it will have a redundant terrestrial link that connects to the first and last wagon of the train. This link will use a moving relay solution in order to achieve reliable communications and reduce fixed infrastructure requirements. This network allows users to access a high-capacity terrestrial communications network that it is distributed inside the train using a wireless network based on the new high-capacity 802.11 standards such as 802.11ac/ad. The satellite link is used as backup link for the terrestrial network. This link currently allows up to 100 Mbps using antennas with automatic azimuth control and low profile elevation that can be simply installed on top of the train, and in the future, the capacity will be increased to 1 Gbps.

The entire communication system requires the use of an IP network along the train with a minimum capacity of 10 Gbps. This will allow managing the traffic of different links: train-land, train-satellite, and intratrain. Interwagon communications can be also done using short distance 10 Gbps wireless links at mmWave or THz, to allow train assembly and to minimize wired connections on trains wagons.

Trains will have an internal 10 Gpbs network for multimedia applications of the passengers, with an external connection of 1 Gbps for Internet connections. Also, in the station, there will be a 100 Gbps network for all the train noncritical services. This station network can have many infrastructure-to-infrastructure communications for additional services as passengers transfer, video surveillance, advertising screens, digital TV, and other new services. As an example of terrestrial network, the current LTE network that can reach capacities of 100–300 Mbps using carrier aggregation on the 1–6 GHz band can be stated and described. This performance can be efficiently used on HST using a moving relay solution on board the train. These links allow reliable communications up to speeds of 350 km/h with the problem that throughput is reduced with velocity when the channel is degraded, as described in. To get higher throughputs, it is necessary to use lower frequency and higher frequency networks together. 

Network Design for Critical and Non-Critical Communications

The design of critical and noncritical communications is completely different from conventional networks. In the first case, it is necessary to make a special design of the network focused on QoS and reliability. In the other case, noncritical communications are focused on capacity. In both cases, the model and design of the communication network are completely different, considering node architecture, handover schemas, relay configuration, Multiple-Input Multiple-Output (MIMO), antennas, and diversity. Then, it is necessary to accurately design the physical interface for each special environment, vehicle dynamic, and passengers or payload requirements. It includes propagation modeling, waveform selection, and antenna design for current communications bands (1–6 GHz), mainly for critical communications and for future mmWave bands (24–34 GHz) for passengers and payload.

High quality of service networks is based on the use of redundant communications to increase reliability and maintainability. For this purpose, railway critical communications use two equal terrestrial networks simultaneously. This solution guarantees an excellent radio coverage and reliability.

Noncritical communications can also use two or more networks at the same time, but, in this case, the design of the network is focused to increase capacity, so two or more networks work in parallel and at the same time guarantee a minimum coverage in complex areas. Usually, high-capacity terrestrial network can be complemented with a satellite link to provide radio coverage on remote areas and with other terrestrial networks to improve capacity on special parts of the track like stations or densely populated areas.

Conclusions

In the above discussion the state-of-the-art wireless communications in smart rail transportation systems have been surveyed and discussed comprehensively. To begin with, the communication requirements and scenarios/links of smart rail transportation are defined in terms of train-to-infrastructure, interwagon, intrawagon, inside station, and infrastructure-to-infrastructure scenarios. Then, regarding the critical communications, the situation of current GSM-R and the trend of future LTE-R are reviewed, and the main critical issues—signal quality on the top of and inside train, chain type network deployment, and guaranteeing QoS for safety services—are highlighted for further study. Moreover, multiple potential solutions of providing noncritical, broadband communications are analyzed. A complex project is highly required to install a network inside the train and several external networks combining terrestrial links in microwave and mmWave bands together with satellite links. For the network planning, usage of redundant communications is the key solution of guaranteeing an excellent radio coverage and reliability of critical communications, while deploying two or more different networks that can work in parallel is of importance of providing noncritical, broadband communications to the onboard users. Last but not least, some principal techniques are highlighted for network radio planning for smart rail transportation systems, including accurate link budget using high-performance ray-tracing methods, new handover scheme avoiding very fast adaptive beamforming and new telecommunication solutions based on multiple radio bearers using cellular and satellite public networks.

Daily Updates from Metro & Railway

LEAVE A REPLY

Please enter your comment!
Please enter your name here

This site uses Akismet to reduce spam. Learn how your comment data is processed.